Sunday, February 7, 2016

Building a Black Iron Pipe and Wooden Coffee table

My kids and I love to play board games.  However, whenever we played, the board game would not fit the ottoman coffee table we had so we would have to move it out of the way and play on the floor.  Walking though the store, I fell in love with the coffee table that went with my dining table in the kitchen.  However, I didn't want my house to be too matchy matchy.  On top of that, the price was over 1K so I wasn't jumping for joy at spending that much for a coffee table. 

Therefore, I decided to make the coffee table myself.  My dining table is made from reclaimed wood and has iron legs so I wanted my coffee table to be somewhat like that.  In the end, this is what I came up with my coffee table and I absolutely love it.

 

I always start my creative building process by scribbling down a drawing of what I think I would like and then I do my research.  I looked up square iron pieces to be similar to my dining table, but of course, I had no soldering experience.  I needed something adjustable so I thought of pipes.  I could get whatever measurements I wanted and put it together like lego pieces. 

I decided to get black iron pipes instead of galvanized ones.  I like the more rustic look and since I was making a coffee table, I didn't need the no rust feature of the galvanized pipes.  I learned rather quickly not to pick up black pipes with your hands because they are covered with grease.  Luckily, I brought some gloves with me when I was shopping (I never go to the hardware store with out them because wood+fingers = splinters). 


I did some research on how to remove the grease.  First I soaked the pipes in Trisodium Phosphate using the instructions on the back.  I found this at Lowes for a few dollars.  With a little elbow grease, I scrubbed the grease off after it had been soaking in the solution.  I used goof off to remove any remaining residue.
 

I quickly dried all the pipes (so that it wouldn't rust) and then started putting them together. 

 

I screwed the caps (which will be like the feet for my coffee table)  to a 4 inch piece of black steel nipple fitting.

 

Next, I  screwed the black steel tee fitting to the 4 inch piece and added a 8 inch piece to the other side.


 

To the center tee fitting, I attached a 12 inch nipple fitting with another tee fitting to attach the pair of legs together.

 

To attach the two pairs together, I added a center piece of black pipe that was 48 inches long. 


Finally, I added 4 flanges to the top of the 8 inch nipples that would enable me to attach it to the table surface from underneath.  I know there are more black pipes on the floor there.  I bought enough to make several different size scenarios.  Originally, my table was bigger, but I scaled it down a bit.  Once I got my leg measurements, I was off to cut the table top.

 

I bought 3 pieces of 2x8x10 and cut them to a length of 56 inches. 


 

Next, since the edges of the wood were curved, I went ahead and stripped each piece so that it would have a nice straight edge.

 

I clamped all the pieces together so that the edges would be straight and then I glued and screwed all the pieces using my kreg jig.

 

Initial assembly looked like this:



I'm well aware of the price tag on the pipes (this was before I cleaned the pipes).  I wanted to make sure my top fit the dimensions of the pipes before washing them.  Next, I sanded the entire piece to remove any rough edges.



Now came the fun part.  I used hammers, chisels, knives, my feet and whatever else I had to make the wood look old.  It was quite therapeutic :)   I wanted to make the wood look old and dented so I pounded it for quite some time.



I stained it with Minwax Walnut color stain that I already had.  I applied 3 coats of polyurethane with light sanding in between to the top surface and just 1 coat underneath.  

 

I added some metal brackets underneath for additional support.  Then I screwed the flanges in place. 

 

With some creative sliding (it is heavy), I flipped the table and voila!

 

So I lived with this table for a week before deciding that it was a little too tall for my liking.  I built it to the height of typical coffee tables, 18.5".  However, I decided that by lowering my table a couple of inches, it would look and feel better.  Even though everyone thought I was crazy because they did not agree with my thoughts, I went to the store and replaced my pipes and rebuilt my table.  I originally had a 10" pipes instead of an 8" ones.  

 

Here we are with my storage ottoman I had before.  I had just reupholster the thing a couple of months prior too, but it just doesn't work in our space anymore.  It once was perfect when we had toddlers, but now it was just too small.




I bought a new rug that made the room much bigger and the ottoman just looked tiny in it.


My new coffee table looked huge in comparison and for a moment I thought it was too big.


 

However, after living with it for a few months, I've discovered, it is indeed perfect.

 


 



I love everything about it.  It is super sturdy, we can fit our board games comfortably and best of all, my kids can dent, color, and scratch it up, and it only adds more character to the surface.  It is definitely a put your feet up type of table which is how we live.


In the end, I saved a bunch.  I ended up spending about a hundred for my coffee table and the best part of my table is that I love it more than the 1K inspirational one.

  

Have you ever built something only to find out that you had to rebuild it to make it perfect?  I do it all the time.  Each piece I learn something new that I am able to apply what I've learned to my next project.  I am so happy with my table.  It took me a while to get there, but I finally did.

Here's a run down of the materials:
3 - 2x8x10
4 - 1 inch floor flange fitting
4 - 1 inch black iron cap fitting
6 - 1 inch black iron tee fitting
4 - 4 inch length (1 inch diameter) black steel nipple fitting
4 - 8 inch length (1 inch diameter) black iron pipe
4 - 12 inch length (1 inch diameter) black iron pipe
1 - 48 inch length (1 inch diameter) black iron pipe
16 screws
2 metal brackets
1 box of tsp
1 spray bottle of goof off
1 quart of stain
1 quart of satin finish polyurethane  

Note that you can make your table any size you want.  I made mine to fit my space and dimension of my couch (and board games ;) )

2 comments:

  1. You stained it so perfectly! Was it a gel stain? I need to stain pine doors to dark/old walnut colour, but not sure if I'll be able to achieve that uniform colour throughout the big flat surface.

    ReplyDelete
  2. It is not gel stain, but the standard stain. I find that the key to uniform staining is to sand sand sand. Getting rid of all the residue that is on the wood helps it absorb the stain. Good luck!

    ReplyDelete

Related Posts with Thumbnails